Kodak PROFESSIONAL LED II 20P User Manual download pdf (Page 77)

Maintaining the Equipment

September 2000 4-3

Periodic Maintenance

Replacing the Air Filter

The air filter under the shoe should be replaced approximately every 3 months.

1. Open the front door of the printer.

2. Pull back the spring fingers.

3. Remove the air filter.

4. Install a new air filter. For parts ordering information, see

“Supplies” on page A-1.

front door

shoe

air filter

spring finger

1 2 ... 72 73 74 75 76 77 78 79 80 81 82 ... 197 198

Regulatory Information 3
Safety Regulations 4
Environmental Regulations 5
Warranty Information 6
Table Of Contents 7
About This Guide 13
About Other Publications 14
Getting Help from Kodak 15
1 Introduction 17
Equipment Overview 18
Rear View 19
2 Using the System 21
Starting up the Printer 22
Calibrating the Printer 23
2-4 September 2000 24
September 2000 2-5 25
Obtaining Densities 26
Completing the Calibration 27
2-8 September 2000 28
Making Prints 29
Shutting Down the Processor 30
Shutting Down the Printer 31
2-12 September 2000 32
September 2000 3-1 33
Operating the Printer 34
OCP Key/Light Descriptions 35
Printer Offline Feature 36
Online Mode 36
Offline Mode 36
Cancelling Jobs 36
Status Messages 37
3-6 September 2000 38
3-8 September 2000 40
screw lock 41
3-10 September 2000 42
September 2000 3-11 43
3-12 September 2000 44
September 2000 3-13 45
Removing the Chad 46
Shutdown and Restart 47
Unload Supply 47
Selecting SCSI Ports 47
Managing a Modem 48
Setting the Paper Length 49
represents the cut edge 50
Setting the Page Starts Value 51
Producing Borderless Prints 52
September 2000 3-21 53
3-22 September 2000 54
Resetting the Defaults 55
About Printing 56
September 2000 3-25 57
Operating the Processor 58
OCP On/Off Light 61
Operational Modes 62
Adjusting the Key Switch Lock 63
• Locked—Operator mode 63
• Unlocked—Key Operator mode 63
Processing a Control Strip 64
Setting the Current Time 65
Setting the Current Date 65
Viewing the On/Off Times 66
Setting the On/Off Times 66
Calibrating the Temperatures 67
Measuring the Flow Rate 68
Managing the Development Time 69
Managing the Material Sensors 70
Computer Reset 71
Loading the Default Values 72
Clearing Error Conditions 73
4 Maintaining the Equipment 75
Maintaining the Printer 76
Periodic Maintenance 77
Maintaining the Processor 78
September 2000 4-5 79
Operational Checks 80
Weekly Maintenance 81
splash guard 82
top rollers 82
light tight cover 83
developer entrance guide 83
feed table 83
entrance sensors 83
Monthly Maintenance 85
4-12 September 2000 86
Adding New Chemistry 88
September 2000 4-15 89
September 2000 5-1 91
Printer Error Messages 92
Printer Paper Path 93
Clearing Printer Paper Jams 101
Processor Error Messages 106
Clearing Error Messages 107
Clearing a Reset Message 107
Clearing Processor Paper Jams 108
Clearing Drive Errors 108
Calibration Troubleshooting 109
Calibration Error Codes 110
Non-Numeric Error Messages 116
Getting Additional Help 117
Appendix A: Ordering Supplies 119
Standard (U.S.) Paper 120
Metric Paper 120
Processor Chemicals 121
Publications 121
Appendix B: Specifications 123
Site Requirements 124
Plumbing 125
Electrical 126
Power Cords 127
Power Outlets 127
Line Frequency 128
Specifications 129
Line Voltage 131
Operating Environment 132
Wash Chemicals 133
Telephone line 133
Densitometer 133
SCSI Cable 134
Information 135
Installation Procedure 136
September 2000 C-3 137
C-4 September 2000 138
September 2000 C-5 139
Adding a Device 140
September 2000 C-7 141
Editing the Log Settings 142
Updating a Device 143
Deleting a Device 144
Viewing Graphs 145
Value Graph 146
Difference Graph 147
History Graph 148
Sending LUTs 149
C-16 September 2000 150
Sending Targets 151
WINDOWS NT Version 152
MACINTOSH Version 153
C-20 September 2000 154
September 2000 C-21 155
C-22 September 2000 156
September 2000 C-23 157
C-24 September 2000 158
September 2000 C-25 159
C-26 September 2000 160
(Macintosh) Tab 161
C-28 September 2000 162
September 2000 C-29 163
C-30 September 2000 164
September 2000 C-31 165
File Formats 166
Installing the Densitometer 167
Server Software 169
Using the Image Print Server 170
Suspending and Resuming 171
Failed Jobs 171
Attended Operation 171
Enqueue Example 172
September 2000 D-5 173
Print Server Software 174
Option Descriptions 175
Enqueue Dialog Box 176
Description 178
Export Module 179
Installing the Software 180
Printing Images 181
E-4 September 2000 182
September 2000 E-5 183
KODAK LED Main Dialog Box 184
Punch Attributes 185
Page Layout Attributes 186
Printer Status Dialog Box 187
Troubleshooting 188
Other Problems 189
September 2000 Index-1 191
Index-2 September 2000 192
September 2000 Index-3 193
Index-4 September 2000 194
September 2000 Index-5 195
Index-6 September 2000 196
198

Comments to this Manuals

No comments

Kodak PROFESSIONAL LED II 20P User Manual Page 77

Comments to this Manuals