Kodak 20R User Manual Page 77
- Page / 166
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Diagnostics and Troubleshooting
September 2000 5-7
96 shoe exit nip made not
detected
The shoe exit nip made switch was
not detected after moving the shoe
exit nip to the nip made position.
Check for a paper jam in the shoe exit
nip area.
97 unexpected deflector
nip made
The deflector nip made switch was
detected after moving the deflector
to the up position.
Check for a paper jam in the deflector
nip area.
98 deflector nip made not
detected
The deflector nip made switch was
not detected after moving the
deflector to the up position.
Check for a paper jam in the deflector
nip area.
99 timeout clearing data
patch
The rotor was not able to be
properly started.
Call for service.
100 xlator start failed The translator failed to start. Call for service.
101 shoe exit nip start failed The shoe exit nip failed to start. Call for service.
102 deflector start failed The deflector failed to start. Call for service.
109 sheet xport ready
timeout
The sheet transport area remains
busy or initializing process is taking
longer than expected.
Call for service.
110 paper detected in
machine
Paper was detected in the printer
while attempting to load a new roll
of paper.
Remove all paper from the printer and
reload the new roll of paper.
111 xlator home failed The translator could not find its
home position after several
attempts.
Call for service.
112 invalid paper width
sensor coverage
The paper is not laying flat over the
paper width sensors or the end of
roll has been reached.
Open the supply door and move the
paper to the correct position.
128 back checksum 0 ROM test failed at powerup. Reinitialize the printer and call for
service.
129 bad checksum 1 RAM test failed at powerup. Call for service.
130 rotor not stopping Rotor will not turn off. Turn off the printer and call for service.
131 xlator at both limits Both the front and back translator
soft limit switches are actuated.
Call for service.
132 knife at both limits Both the front and back knife limit
switches are actuated.
Call for service.
133 timeout sheet xport
reply
The 300 board does not reply to the
200 board within the expected
amount of time.
Call for service.
134 duart self test failed Duart test failed when the printer
was turned on.
Call for service.
192 –
219
Various software error
messages.
A software problem has occurred. Shut down and restart the printer.
Call for service.
Error
Code
Error Message Possible Cause Possible Solution
- © Eastman Kodak Company, 2000 2
- Regulatory Information 3
- Safety Regulations 4
- Environmental Regulations 4
- Warranty Information 5
- Table Of Contents 7
- About This Guide 13
- About Other Publications 14
- Getting Help from Kodak 15
- 1 Introduction 17
- Equipment Overview 18
- 2 Using the System 19
- Calibrating the Printer 20
- September 2000 2-3 21
- 2-4 September 2000 22
- Obtaining Densities 23
- Completing the Calibration 24
- September 2000 2-7 25
- Making Prints 26
- Shutting Down the Printer 26
- Hard Shutdown 27
- 3 Operating Procedures 29
- Operator Control Panel (OCP) 30
- OCP Key/Light Descriptions 31
- 3-4 September 2000 32
- Status Messages 33
- Removing the Supply Cassette 34
- Loading the Paper 35
- screw lock 36
- September 2000 3-9 37
- 3-10 September 2000 38
- September 2000 3-11 39
- 3-12 September 2000 40
- September 2000 3-13 41
- Preparing the Takeup Cassette 42
- September 2000 3-15 43
- 3-16 September 2000 44
- September 2000 3-17 45
- 3-18 September 2000 46
- September 2000 3-19 47
- Removing the Takeup Cassette 48
- September 2000 3-21 49
- • screw lock or flange 50
- Using the Printer Features 51
- Shutdown and Restart 52
- Selecting a Loading Option 52
- Paper Loading Options 53
- Supply Roll 54
- Setting the Punches 55
- 3-28 September 2000 56
- Using the Automatic Roll ID 57
- Using Page Starts 57
- Setting the Page Starts Value 58
- Producing Borderless Prints 58
- Resetting the Defaults 59
- Selecting the SCSI Ports 60
- Setting the Target Pad Reads 60
- Selecting A Modem 61
- Setting the Time and Date 61
- Setting the Current Day 62
- Changing the Gutter Width 63
- 3-36 September 2000 64
- About Printing 65
- 3-38 September 2000 66
- 4 Maintaining the Equipment 67
- Removing the Punch Chad 68
- Periodic Maintenance 69
- Printer Error Messages 71
- Printer Paper Path 72
- Clearing Paper Jams 79
- 5-10 September 2000 80
- Calibration Troubleshooting 84
- Non-Numeric Error Messages 91
- Getting Additional Help 92
- Appendix A: Ordering Supplies 93
- Standard (U.S.) Paper 94
- Metric Paper 94
- Leaders and Splice Tape 95
- Publications 95
- Appendix B: Specifications 97
- Operator and Service Access 98
- Floor Requirements 98
- Electrical 99
- Power Cords 99
- Power Outlets 100
- Line Frequency 100
- Line Voltage 101
- Specifications 102
- Telephone line 104
- Densitometer 104
- SCSI Cable 104
- Operating Environment 104
- Information 105
- Installation Procedure 106
- September 2000 C-3 107
- C-4 September 2000 108
- September 2000 C-5 109
- Adding a Device 110
- September 2000 C-7 111
- Editing the Log Settings 112
- Updating a Device 113
- Deleting a Device 114
- Viewing Graphs 115
- Value Graph 116
- Difference Graph 117
- History Graph 118
- September 2000 C-15 119
- Sending LUTs 120
- Sending Targets 121
- WINDOWS NT Version 122
- MACINTOSH Version 123
- C-20 September 2000 124
- September 2000 C-21 125
- C-22 September 2000 126
- September 2000 C-23 127
- C-24 September 2000 128
- September 2000 C-25 129
- C-26 September 2000 130
- (Macintosh) Tab 131
- C-28 September 2000 132
- September 2000 C-29 133
- C-30 September 2000 134
- September 2000 C-31 135
- File Formats 136
- Installing the Densitometer 137
- Server Software 139
- Using the Image Print Server 140
- Suspending and Resuming 141
- Failed Jobs 141
- Attended Operation 141
- Enqueue Example 142
- September 2000 D-5 143
- Print Server Software 144
- Option Descriptions 145
- Enqueue Dialog Box 146
- File Format Details 148
- Supported Tags 148
- *” are image dependent 148
- LZW Compression 148
- Export Module 149
- Installing the Software 150
- Printing Images 151
- E-4 September 2000 152
- September 2000 E-5 153
- KODAK LED Main Dialog Box 154
- Punch Attributes 155
- Page Layout Attributes 156
- Printer Status Dialog Box 157
- Troubleshooting 158
- Other Problems 159
- September 2000 Index-1 161
- Index-2 September 2000 162
- September 2000 Index-3 163
- Index-4 September 2000 164
- 166
Related products and manuals for Multifunctionals Kodak 20R
Multifunctionals Kodak A-61555 User Manual
(108 pages)
(108 pages)
Multifunctionals Kodak 5.1 User Manual
(115 pages)
(115 pages)
Multifunctionals Kodak 6J7611A User Manual
(80 pages)
(80 pages)
Multifunctionals Kodak 20P User Manual
(198 pages)
(198 pages)
Multifunctionals Kodak 3953783 Datasheet
(2 pages)
(2 pages)
Multifunctionals Kodak ESP 5210 User's Guide
(72 pages)
(72 pages)
Multifunctionals Kodak ESP 5250 User's Guide
(18 pages)
(18 pages)
© 2020, manymanuals.com. All rights reserved. | 0.775 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals