Kodak NOVAJET 750 User Manual

NovaJet 750 Printer TTrraaiinniinngg GGuuiiddee Ink Installation Printer Calibrations Routine Maintenance Preventive Maintenance Cartridg

NJ750 Training Guide 10 C. Routine Maintenance 1. Perform routine maintenance at recommended plot time hours and in accordance with prescribed do

NJ750 Training Guide 11INTERVAL COMPONENT CLEANING AGENT 10-20 Hours Cartridge Jet Area NovaKlean on lint-free Towel 50-75 Hours

NJ750 Training Guide 12INTERVAL COMPONENT CLEANING AGENT 50-75 Hours Flex Driver Cables NovaKlean on lint-free Towel Ensur

NJ750 Training Guide 13INTERVAL COMPONENT CLEANING AGENT As Required Paper Sensor Isopropyl Alcohol on cotton swab The Paper S

NJ750 Training Guide 14D. Preventive Maintenance Perform preventive maintenance at recommended plot time hours and in accordance with prescribed do

NJ750 Training Guide 15E. Cartridge Checklist (for warranty replacement) 1. Electrically bad jets (100% filled block) in the Prime pattern (10 noz

NJ750 Training Guide 16F. Advanced Troubleshooting 1. Skewing of the output image is normally a dirty or defective encoder strip/sensor. Clean

NJ750 Training Guide 17 4. Faint cut lines or heavy lines which angle slightly on one end are caused by the carriage head hitting the media surface

NJ750 Training Guide 18 7. Larger than normal ink droplets (0.5- 2 mm) on the media are caused by excessive pressure in the cartridge. Ensure the

NJ750 Training Guide 19Ensure the diagonal lines in the prime pattern are solid and exhibit consistency. Up to 20 jets may be compensated in each c

NJ750 Training Guide 2 Installed needle assembly Do not break connection when installing new cartridge 25 ml inside - preprimed A. Ink Installatio

NJ750 Training Guide 20 10. Ink over spray can be caused by compression utilities. Electrostatic discharge from film media has also been known to

NJ750 Training Guide 21 13. Vertical banding through an image can be caused by mottling of the ink on low saturation media like bond, the

NJ750 Training Guide 2215. For initialization failures first ensure the memory module is properly seated at the Main PWA (remove 5 screws to access

NJ750 Training Guide 2317. For NJ750 and 800 series dryer system failures ensure the logic cable and power cable are properly secured. Check senso

NJ750 Training Guide 24Received IP Address192.168.002.010Ok G. Print Server Networking (SEH Intercon print server) A. The 100baseTX parallel pri

NJ750 Training Guide 25Configuration for Windows 2000/XP Printer Networking is a basically a 3-step Process: 1. Assign TCP/IP address of host compu

NJ750 Training Guide 26 NOTE: Before you can configure a Windows print queue, you must first configure an IP address on both your PC and the SEH p

NJ750 Training Guide 27 Alternate DNS Server- 192.168.254.190 Leave the Gateway blank. See Figure Below. NOTE: To configure the SEH p

NJ750 Training Guide 28 2. To assign your IP address and Subnet Mask, choose TCP/IP from the configuration tree on the left. Assign 192.168.254

NJ750 Training Guide 29 3. Close the InterCon-NetTool. Your settings will be saved in the print server. You are now ready to setup the Windows Prin

NJ750 Training Guide 3 a) Prime line using the short needles (purple in color); attach short needle to each of the 4 valves. Connect septum needle

NJ750 Training Guide 30 5. Under “Printer Name or IP Address” enter 192.168.254.200. The “Port Name” will self generate. Click Next. See figure be

NJ750 Training Guide 316. Under “Device Type” select “Network Print Server (1 Port)” the first one in the list. Click Next, then Finish. See figu

NJ750 Training Guide 32 4. RASTER IMAGE PROCESSOR (RIP) TCP/IP ASSIGNMENT 1. The last step of the networking setup is to assign an IP address in

NJ750 Training Guide 4down a solid band of color with 33% ink load. Color Test Failures: - Example A above depicts complete ink starvat

NJ750 Training Guide 5

NJ750 Training Guide 6Jet is bad; jet re-addressedautomaticallyJet is clogged (Jetelectronics aregood though)Jet manuallybypassed,jet goodJet manual

NJ750 Training Guide 733.00 inchesDistance between the two“T’s” should be 33.00” +/-0.05” (inches) B. Printer Calibrations A. Paper Axis Test P

NJ750 Training Guide 8 D. Color Calibration To activate the Color calibration select Utility Menu - Color Calib. Menu – Calib Test (NJ850: Both Ve

NJ750 Training Guide 92. Advance the media though the printer about 1 foot, using the Feed Media Menu/Forward button. 3. Put the printer media fee