Navitar Xenon 560/750High Intensity Slide ProjectorThe World Leader in Image Quality
Read these instructions carefully before you remove the projector andother components from the container.1. Remove contents from shipping container an
IMPORTANT: BEFORE OPENING THE BOX CONTAINING THEXENON BULB, NOTE THE FOLLOWING PRECAUTIONS: TheXenon bulb contains gas under pressure. Care should
7. While holding the positive wire end post firmly, remove the end capand washer (if supplied) from the bulb. Insert the screw end of thebulb into t
14. After installing the bulb, it will be necessary to adjust the bulbposition in order to render even illumination across the screen.Position the pro
Note: An arc correcting magnet is used to make an even flow of elec-trodes to prevent a partial overheat of the lamp. In the arrangement, asillustra
Supply a.c. power of the rated voltage and frequency. The power con-sumption is about 1.5KW. The power line must be capable of handlingthe total cur
13. When turning the projector off, rotate the operating switch counterclockwise one step. The lamp will go off, but the fan will continueto operate
109Contact OutputCoupler Output87654321107 63EmitterCollector8952 14REMOTE-2 Connector (Receptacle10P)This connector is used to turn the Xenon project
The lamp can be positioned for uniform screen illumination by adjustingthe screws with a screwdriver through three (3) holes on the side of thelamp ho
6. When you have accomplished the centering of the cone of light onthe screen, install a slide frame (without film or glass). Readjust thescrews so t
Warning ∆∆∆∆∆ WarningIMPORTANT: BEFORE OPENING THE
Slide burning and picture flicker are problems common to Xenon projec-tors. The following is an explanation and remedy for these problemswhich can oc
If the flickering problem is still apparent after readjusting the lampposition, a magnet adjustment may be needed.1. Please follow all safety precauti
In room environments with high humidity, the use of a high poweredXenon slide projector or modified halogen lamps may cause the moisturethat is trappe
If you ordered the NAVITAR XENON 560/750DM, the dissolve modulehas been attached at the factory. Skip to the section Connecting theDissolve Interfac
The shutter blades can be opened automatically by turning the three set-up switches on the dissolve interface box to the ON position. Rememberto retu
1. Remove two (2) screws on the side of the dissolve module and takeoff the square cover on the dissolve module. Turn on the powerswitches for the AV
Projector must be on a flat, stable surface.The Xenon lamp is under pressure. Protect yourself from theunlikely, but possible explosion of the lamp
The Xenon lamp is an excellent light source for slide projectors becauseit produces brilliant light of high color temperature. This is an ozone-freel
1. Starter Assembly 1A816S029-012. Blower 1A165F044-013. Circuit Breaker 1A151C011-034. Rotary Switch 1A154A084-015. Terminal 1J171Y043-106. Transform
1. Starter Assembly 1A816S029-022. Blower 1A165F045-013. Circuit Breaker 1A151C011-014. Rotary Switch 1A154A084-015. Terminal 1J171Y043-106. Transform
2 Warning 3 Introduction 3 Supplied Components 3 Service & Repair 4 560/750 System Diagrams 6 Features 8 Installing a New Lamp13 Operating
SYMPTOM CAUSE/REMEDYPower is not supplied. Is the power cord connected? Replace the power cord.Is there a connection to the main switch?Replace the m
29560AF/DM Schematic Diagrams
30750AF/DM Schematic Diagrams
31560 & 750 RAK/RARS232 Schematic Diagrams
Brightness (Lux) 4300Color Temperature 5800ºKLamp Quartz-Xenon, high pressure arcPower 550 wattsBulb Life 500-1000 hours depending on usageReflector C
Brightness (Lux) 5400Color Temperature 6450ºKLamp Quartz-Xenon, high pressure arcPower 750 wattsBulb Life 500-1000 hours depending on usageReflector C
An ozone-free type lamp is used for this projector. The ratings are asfollows:560AF/560DM560RAK/560RARS-232Navitar Part # XB-560Rated Input Power 550
The dissolve interface receives signals from an AVL/Dataton DissolveController and controls three (3) 560DM/750DM Series Xenon SlideProjectors.Compone
AC In ConnectorConnects the power cord attached to the unit.50 or 60Hz Change SwitchDepending on the cycle of input power, turn to 50 for 50Hz and tur
Connect the Navitar Dissolve Interface to your 560DM/750DM SeriesXenon Slide Projector and an AVL/Dataton dissolve controller. Connectthe OUT Connect
WarningWarning ∆∆∆∆∆Xenon Lamp Contains Gas Under
Examples of Connections Navitar Dissolve Interface MDC20038To Audio AmpCue SignalAVL TypeInput
This product is warranted to be free from defect in material and work-manship for a period of one year from the date of invoice to the originalpurchas
NAVITAR, Inc.200 Commerce DriveRochester, NY 14623 USA(716) 359-4000 phone(716) 359-4999 faxWarning ∆∆∆∆∆Xenon Lamp Contains Gas Under Pressure.Read I
The Navitar Xenon Slide Projector is so bright you can make slide pre-sentations with the room lights on. Even more important, you wontloose your au
Top ViewSide View 560/750 System Diagrams4Slide GateAuto FocusFocus KnobCaution
Front View 560/750 System Diagrams5Rear ViewLens PortStorage CompartmentPower C
Slide ProjectorModels 560AF/DM and 750AF/DM use a Kodak Ektagraphic-III AMTmodified for our Xenon light source.Models 560RAK/RARS-232 and 750 RAK/RARS
Forward/Reverse Transfer SwitchLocated on the rear part of the projector, it moves the slide tray forwardand reverse.Power ConnectorConnects the main
Comments to this Manuals